Badger Meter Oval Gear EPM2-STD User Manual Download Page 3

AUT-UM-00933-EN-06

Safety 

SAFETY

IMPROPER GROUNDING, POOR VENTILATION, OPEN FLAMES OR SPARKS CAN CAUSE A HAZARDOUS CONDITION AND 

RESULT IN AN EXPLOSION OR FIRE AND CAUSE SERIOUS INJURY.

•   Be sure the fluid system is properly grounded . See your pump instruction manual for details .
•  If there is static sparking or if you feel an electric shock while using the meter, stop dispensing immediately . Identify and 

correct the problem before continuing .

•  Provide fresh air ventilation . This will avoid the buildup of fumes from the fluid being dispensed .
•  Do not smoke while dispensing flammable fluids .
•  Keep the dispensing area free of debris including solvents, rags and spilled gasoline . 

EQUIPMENT MISUSE CAN CAUSE THE METER TO RUPTURE OR MALFUNCTION AND CAUSE SERIOUS INJURY.

•  This equipment is for professional use only .
•  Read all instructions, tags and labels before operating the equipment .
•  Use the equipment only for its intended purpose .
•  Do not modify or alter the equipment .
•  Do not leave equipment unattended while dispensing .
•  Check equipment daily . Repair or replace worn or damaged parts immediately .
•  Do not exceed the maximum working pressure level of the lowest rated system component .
•  Use only extensions and nozzles that are designed for use with this equipment .
•  Use only fluids and solvents that are compatible with the equipment . Read all fluid and solvent manufacturer’s warnings .
•  Tighten all fluid connections before operating this equipment .
•  Do not stop or deflect leaks with hands, body, gloves or rags .
•  Do not dispense towards any person or any part of the body .
•  Do not place hands or fingers over the end of or into the dispense valve .
•  Comply with all local, state, and federal fire, electrical and safety regulations
•  Use of this product in a manner other than specified in this manual may result in impaired operation or  

damage to equipment . 

THIS METER IS DESIGNED SPECIFICALLY TO DISPENSE PETROLEUM PRODUCTS. DO NOT USE FOR ANTIFREEZE 

(ETHYLENE GLYCOL) SOLUTION, WINDSHIELD WIPER FLUID, BRAKE FLUID AND WATER BASED SOLUTIONS

Page 3 

April 2019

Summary of Contents for Oval Gear EPM2-STD













Reviews: