Badger Meter Oval Gear EPM2-STD User Manual Download Page 11

AUT-UM-00933-EN-06

Specifications 

SPECIFICATIONS

Maximum flow *

10 gpm (38 lpm)

Minimum flow *

0 .25 gpm (1 lpm)

Operating pressure (maximum)

1000 psi (67 bar)

Operating pressure (minimum)

5 psi (0 .35 bar)

Operating temperature (maximum)

120° F (50° C)

Operating temperature (minimum)

20° F (–5° C)

Accuracy (general)

± 0 .5%

Accuracy (anti-freeze)

± 1 .5%

5-digit LCD display

Quarts, Pints, Gallons, Liters

Inlet and outlet connections

1/2 in . NPT (1/2 in . BSPP)

* Minimum and maximum flow range will vary with fluid viscosity

Table 4:  Part numbers: inside meter

PARTS

 

 

1

2

Figure 16:  Parts: back of meter

Figure 17:  Parts: front of meter

Item

Description

Part Number

Item

Description

Part Number

1

Battery holder assembly

64103-026

1

Display assembly

64103-023

2

Bottom case with screws

64103-003

2

EPM2 std . register assembly

64103-024

Table 5:  Part numbers - back of meter

Not shown

Swivel, NPT, special fluids

64082-001

Not shown

Rubber boot

65546-001

Table 6:  Part numbers - front of meter

Page 11 

April 2019

Summary of Contents for Oval Gear EPM2-STD













Reviews: