Badger Meter Blancett B2800XP, User Manual

Page: 10 / 20

Meter Type
At the METERTYP prompt, press
ENTEO
The current meter type displays If the current selection is correct, press
ENTEO
to advance to the next parameter To change the type, press
UP
or
OIGHT
Press
ENTEO
to save and advance to the next
parameter If GAS is selected, the operating pressure (psig) and operating temperature (° F) must be entered If LIQUID is
selected, the monitor advances to the DAMPING parameter
OTEE: N
The 4…20 mA zero and span values are not factory set
Operating Pressure
At the OP PRES prompt, press
ENTEO
The first digit of the current setting flashes If the current setting is correct, press
ENTEO
to advance to the next paramter To change the current setting, press
OIGHT
to move to the correct digit Press
UP
to
increment the digit until it matches the new operating pressure Repeat for all digits Press
ENTEO
to save and advance to the
OP TEMP parameter
Operating Temperature
At the OP TEMP prompt, press
ENTEO
The first digit of the current setting flashes If the current setting is correct, press
ENTEO
to advance to the next paramter To change the current setting, press
OIGHT
to move to the correct digit Press
UP
to
increment the digit until it reaches the new operating temperature Repeat for all digits Press
ENTEO
to save and advance to
the DAMPING parameter
Damping Factor
The damping factor is increased to enhance the stability of the flow readings, and decreased to allow the flow meter to react
faster to changing values of flow This parameter can be any value 0…99 with 0 being the default
At the
DAMPING prompt, press
ENTEO
The first digit of the current damping setting flashes If the current selection is correct,
press
ENTEO
to advance to the next parameter To change the damping factor, press
UP
to increment the digit Press
OIGHT
to move to the next digit After all digits are entered, press
ENTEO
to save and advance to the PULS OUT parameter
Totalizer Pulse Output
The pulse output parameter can be either enabled or disabled When enabled, this output generates a 20 mS duration pulse
for every time the least significant digit of the totalizer increments The amplitude of the pulse is dependent on the voltage
level of the supply connected to the pulse output and is limited to a maximum 30V DC
Linearization
Linearization enhances the accuracy of the display The linearization accepts a maximum of ten points and requires additional
calibration data from the meter being used with the monitor Typically, calibration information can be obtained in three,
five and ten points from the flow meter’s manufacturer If linearization is not needed, press
OIGHT
to advance to the next
parameter To complete linearization, press
ENTEO
at the LINEAR prompt The meter advances to the NUM PTS parameter
Number of Points
If the number of points is set to 0 , linearization is disabled Press
ENTEO.
The most significant digit of the number of points
entry begins to flash The first number can be a 1 or a 0 only Press
UP
to increment the first digit Press
OIGHT
to move to the
least significant digit When both digits have been entered, press
ENTEO
to save and advance to the FREQ 1 parameter
Frequency
At the FREQ 1 prompt, press
ENTEO.
The first digit of the first linear point’s frequency input flashes If the first frequency is
correct, press
ENTEO
to advance to the next parameter To change the frequency, press
UP
to increment the digit Press
OIGHT
to move to the next digit After all digits are entered, press
ENTEO
to save and advance to the COEFF 1 parameter
Coefficient
The coefficient is the value applied to the nominal K-factor to correct it to the exact K-factor for that point The coefficient is
calculated by dividing the actual K-factor for that point by the average K-factor for the flow meter
Coefficient =
Average K-Factor
Actual K-Factor
At the COEFF prompt, press
ENTEO.
The first digit of the coefficient flashes If the first coefficient is correct, press
ENTEO
to advance to the next parameter To change the frequency, press
UP
to increment the digit Press
OIGHT
to move to the
next digit Repeat for all digits After all digits are entered, press
ENTEO
to save and advance to the next set of linear points
Continue entering pairs of frequency and coefficient points until all data has been entered Press
MENU
twice at the NUM PTS
prompt to exit to the LINEAR prompt Press
OIGHT
to advance to the PASSWORD parameter
Programming
Page 10 March 2017 DSY-PM-00279-EN-03