Bad Boy 1025H Operator'S Manual Download Page 65

Page: 65 / 144

4-13

OPERATION DESCRIPTION

GLOW INDICATOR

This comes on while the engine pre

heating function is activated. It goes off

as soon as preheating is completed.

(1) Glow Indicator

111

COOLANT TEMPERATURE

WARNING LAMP

ENGINE WARNING LAMP

If this lamp comes on, coolant is

overheated.

It comes on when the engine is mal

functioning.

(1) Coolant Temperature Warning Lamp

(1) Engine Warning Lamp

111



When the coolant temperature

warning lamp comes on, cool-

ant is overheated so check the

coolant.



Coolant temperature over 5

℃

1 sec. or shorter / Less than

℃

: 3 - 30 seconds

NOTE

CAUTION



When Engine warning lamp is it,

ensure that you operator the trac-

tor only after the engine RPM

reaches at the normal speed if

this instruction is not kept, it may

cause a performance degradation

or accident due to a system error.

1025H.indb 13

2021-07-06 오전 11:07:43

Summary of Contents for 1025H

















































































































































Search results

Summary of Contents for 1025H

Reviews:

Related manuals for 1025H

Brands by name

Popular brands

Bad Boy 1025H, Operator'S Manual

Search results

Summary of Contents for 1025H

Reviews:

Related manuals for 1025H

Brands by name

Popular brands