Bad Boy 1025H Operator'S Manual Download Page 11

Page: 11 / 144

FOR YOUR SAFETY

Pay attention to the shoulder of

the road;

•

When moving along the un-

paved road with ditches or

slanted sides, pay attention to

the shoulders.

If this instruction is ignored,

there is a risk of falling over.

Interlock the brake pedals (left

and right) when driving on a

road;

•

Make sure to interlock the

brake pedals (left and right)

when driving on a road

If this instruction is ignored,

there is a risk of abrupt turning

or overturning due to one-sided

braking.

Start the machine slowly after

reminding bystander;

•

Start the engine after remind-

ing bystanders of your inten-

sion. Do not start the machine

abruptly.

If this instruction is ignored, un-

expected accident or injury can

happen.

WARNING

1025H.indb 5

2021-07-06 오전 11:07:32

Summary of Contents for 1025H

















































































































































Search results

Summary of Contents for 1025H

Reviews:

Brands by name

Popular brands

Bad Boy 1025H, Operator'S Manual

Search results

Summary of Contents for 1025H

Reviews:

Brands by name

Popular brands