Bad Boy 1025H Operator'S Manual Download Page 15

Page: 15 / 144

FOR YOUR SAFETY

Observe all relevant regulations

for disposal;

•

Be sure to observe all relevant

regulations when you dispose

of the engine oil, transmission

oil, fuel, coolant, filters and

battery.

•

Never dispose the used oil di-

rectly to the river or drainage,

follow legal procedures.

WARNING

No smoking or open flame when

fueling;

•

Do not smoke or use match or

lighter while refueling.

If this instruction is ignored, fuel

can catch fire and lead to explo

sion or fatal injury with burn.

WARNING

Observe all relevant regulations

for disposal;

•

Careless disposal of waste

product can be harmful to en-

vironment and ecosystem.

•

When draining the fuel and oil,

use a proper container that is

not leaking, not food or bev-

erage containers to prevent

from drinking. Do not bury the

waste product in the ground

or dispose to drainage.

WARNING

1025H.indb 9

2021-07-06 오전 11:07:33

Summary of Contents for 1025H

















































































































































Search results

Summary of Contents for 1025H

Reviews:

Related manuals for 1025H

Brands by name

Popular brands

Bad Boy 1025H, Operator'S Manual

Search results

Summary of Contents for 1025H

Reviews:

Related manuals for 1025H

Brands by name

Popular brands