background image

PLAYGROUND, INC. GYM SETS USE A FEW STANDARD CONNECTIONS.

BECOMING FAMILIAR WITH THESE CONNECTIONS WILL SIMPLIFY ASSEMBLY

AND INSURE A SAFER PLAY PRODUCT FOR YOUR CHILDREN.

USING THE HARDWARE

Failure to replace
this bolt with a
shorter one could
result in personal injury.

Check  the  positioning  of  parts  in  each  Step's  illustration,  noting  which  of  the  parts  should 

receive the Spike T-Nut.  Place the Spike T-Nut in the hole and then seat it with one or two taps of a 
hammer.  Align the holes in the parts to be fastened. Start preliminary tightening of bolt into seated 
nut by hand. 

To 

securely  tighten

,  turn  the  bolt  with  a  wrench  until  the  lock  washer  is  fully  compressed 

between the head of the bolt and the flat washer.

Note that in some steps the instructions say to tighten "

just snug

.

"  This means to tighten the 

bolt just enough to keep the parts together, but loose enough to allow the parts to move.  This is 
necessary to allow squaring and leveling.  The bolt will be tightened securely in a following step.  
All bolts and screws must be tightened securely before the playset is ready for use.

Bolt  has  been 

screwed  securely 
into Spike T-Nut and 
the  connection  is 
tight.

  Check  connec-

tions periodically for 
tightness during the 
life of the Gym set. 

Lock Washer

Hex Head

Bolt

Flat

Washer

Spike T-Nut

How to use Hex Head Bolts and Spike T-Nuts

Correct

Assembly

Do not

over tighten.

Typical Installation -Lag Screw:

Typical Installation -Wood Screw:

• Use an electric drill or screw gun to drive screws.
• These screws are self-tapping, so no pilot 
holes are required.
• Lubricate the threads of the screws 
with beeswax or soap to ease 
installation and minimize breaking 
screws.
• 

It is very important to make certain 

that the tops of all screws are flush 
with the surface of the wood and 
there are no protruding sharp edges.

• 

 

Always drill pilot holes 
when using Lag 
Screws.  The size of 
the pilot hole will be 
specified in the Step.

• 

 Tap the head of the Lag

 

Screw with a hammer to 
start the threads into the 
wood and then use a ½" 
socket to tighten.

Lag Screw

Flat

Washer

Lock

Washer

• 

 DO NOT over tighten

• 

 DO NOT over tighten

•  DO NOT DRIVE

TOO DEEP

AND CAUSE

SPLINTERING

•  DO NOT DRIVE

TOO DEEP

AND CAUSE

SPLINTERING

Page 6 - USING THE HARDWARE

TIP: 

Tap the Spike T-Nut into the part before you position the part on the structure.  If you put it in 

the wrong hole, remove it by inserting a bolt from the opposite side of the board and tapping the 
bolt lightly with a hammer.

Incorrect Assembly

During assembly or maintenance, do not over tighten 
the bolts.  Over tightening can cause the bolt to 
protrude past the spiked tee nut, which could cause 
personal injury.  Over tightening can also cause the 
wood to be compressed or to “sink in” the bolt, washer 
or spiked tee nut.  If this has happened, you may need 
to add additional washers or replace the bolt with a 
shorter one, so that the bolt does not protrude.

  

  

© Leisure Time Products Inc.

Next Generation 5007 10-0409 Version 4

Meijer.com

Summary of Contents for Next Generation 5007

























































































Reviews: