background image

SAFETY AND ASSEMBLY INFORMATION

Assembly Safety:

• Keep the work area clean and clear of obstructions.
• Children should stay out of the work area until the safe play area is cleared of obstacles, the gym set has been completely 
assembled, all hardware has been tightened and checked and all tools have been picked up.
• Keep children off the gym set until it has been completely assembled.
• Some parts of the assembly process may require help from another competent adult.
• Do not stand on the platform until the gym set has been completely assembled.  Use a step ladder if you can not reach high 
enough.
• Follow the manufacturers' safety recommendations for the tools and equipment you use.
• 

Avoid assembling your gym set in poor weather conditions.

• 

Wear proper clothing and safety equipment (safety glasses, boots and gloves) while assembling your gym set.

Tools and Materials Required:

Claw Type Hammer

10 ft. Tape Measure

Framing Square or Level

10 ft. Step Ladder

Box Wrench or Sockets (9/16” & ½")

Screwdriver (Medium Phillips)

Electric Drill or Cordless

Beeswax or Soap

Drill Bits:  3/16", 3/8" 5/16" & 7/16"(High Speed)

(Used to lubricate screw threads)

HAVING THE PROPER TOOLS ON HAND WILL EASE AND

REDUCE THE ASSEMBLY TIME OF YOUR NEW PLAYSET.

YOUR PLAYGROUND, INC READY-TO-ASSEMBLE PLAYSET IS STAINED AT

OUR FACTORY.  STAINING IS NOT NEEDED AT THE TIME OF INITIAL ASSEMBLY.

Page 3 - SAFETY & ASSEMBLY INFO

POLYETHYLENE ENCASED POSTS:

Some lumber inside the polyethylene encased posts MAYBE 

subject to the following treatment

Supplier:

Pacific Wood Preserving
22125 Rock Creek Rd.
Sheridan, OR  97378

Preservative:

Pacbor Treated (Disodium 

Octaborate Tetrahydrate)

Retention level:

.118 pcf

Wood species:

Pine, White Fir, Hem Fir, 

and/or Doug Fir

THE WOODEN PARTS FOR YOUR PLAYSET ARE MADE FROM

CYPRESS AND OTHER UNTREATED NATURALLY DECAY RESISTANT LUMBER,

WITH THE FOLLOWING, POSSIBLE EXCEPTIONS:

© Leisure Time Products Inc.

Next Generation 5007 10-0409 Version 4

Meijer.com

Summary of Contents for Next Generation 5007

























































































Reviews: