Backyard Discovery GABLE 8' x 8' Assembly Manual Download

Page: 51 / 56

• Follow directions provided by manufacturer and these instructions.

SHINGLES

- NOT INCLUDED -

Install rst starter row upside down and color up with a 1" overhang at back and bottom of roof panel. Use (4) nails per shingle.

Starter row must be straight and level all the way across with lower edge of roof deck.
NOTE:

If you have installed drip edge install shingles ush to drip edge.

BEGIN

TABS UP

Shingle overlaps

roof decking.

1" (2,5 cm) overhang
past roof deck.

1" (2,5 cm) overhang or

Á ush with drip edge.

(4) Nails

BACK OF

SHED

FRONT OF

SHED

NEVER DRIVE FASTENERS INTO OR ABOVE SEALING STRIPS.

Familiarize yourself with a 3-Tab Shingle.

SHINGLE NAIL PATTERN

(2,5 cm)

NAILS

Sealing Strip

(2,5 cm)

1/2"

(1,3 cm)

Full Rain Slot

Half A Rain Slot

Notch

Summary of Contents for GABLE 8' x 8'

























































Search results

Summary of Contents for GABLE 8' x 8'

Reviews:

Related manuals for GABLE 8' x 8'

Brands by name

Popular brands

Backyard Discovery GABLE 8' x 8', Assembly Manual

Search results

Summary of Contents for GABLE 8' x 8'

Reviews:

Related manuals for GABLE 8' x 8'

Brands by name

Popular brands