manualshive.com logo in svg

Bacharach MVR-SC, User Manual

Share
Download
Bacharach MVR-SC User Manual Download Page 23

 

1100-2294 Rev 1 

23 

4  Upload the Floorplan to Memory 

4.1  System Startup  

1.  Power up the MVR-SC.  When the System Startup (Home) screen appears, access 

System Settings

. 

2. 

After the System Setting screen appears, insert the USB stick containing the floorplan 
spreadsheet into the appropriate slot of the controller. 
 
Note: Instructions on filling out this spreadsheet can be found in 

Section 3

, 

Installation 

3. 

Network Overview

 

IMPORTANT: 

Prior to installation, download the MVR-SC floorplan spreadsheet 

available from MyBacharach.com or on the USB stick supplied with the 
controller. This spreadsheet has editable fields for Floor / Room and non-editable 
fields for Modbus ID and Gateway IP address. The floor and room fields are to be 
completed prior to installation in order to ensure correct wiring and function. 

Up to 100 MVR-300 devices can be connected to the MVR-SC.  These are to be grouped as 
Modbus RTU daisy-chain segments of up to 15 devices, terminating at a Gateway.  Up to 
seven gateways can be used in a fully populated network.  

Gateways connect via an Ethernet TCP network, through an Ethernet switch, to the MVR-SC. 
Up to seven gateways can be used in a fully populated network. The MVR-SC provides 
centralized monitoring of all devices in the network, with a 15-second scan rate. 

When creating the floorplan, follow these conditions:  

 

Keep daisy-chain segments of MVR-300 devices as near as possible to the 
gateway to which they connect.   

Figure 21 - System Status screen 

Summary of Contents for MVR-SC










































Reviews:

No comments

Brands by name

Popular brands

Load more brands