1
Ensure you read this user guide before installing and
using the product.
Babysense is a high quality, high sensitivity electronic
device, which must be handled with care:
• Do not handle roughly, drop or throw.
• Follow the installation instruction carefully to ensure
the device is installed securely and correctly.
• Babysense is not a toy. Do not allow children of any
age to play with it.
• Do not put any additional baby or pet in the bed.
Babysense cannot be used for two infants in one bed.
• Do not operate the unit in the presence of
electromagnetic interference.
• Portable and mobile RF communications equipment
may effect operation of this device.
• You must undertake the performance test daily and
every time you move the monitor, change bedding or
relocate crib/bed position (as set out on page 3).
• Do not operate vaporizer or ventilator directly towards
the bed.
• To avoid possible danger from sensor cords, ensure
that excess cords are pulled back under the mattress,
secured with the included cable tie and are not visible
or reachable.
• Install 4 new and identical size AA 1.5 volt batteries,
preferably alkaline.
•
IMPORTANT:
It is strongly advised that parents and
caregivers learn how to give first aid.
• Please remove batteries if the device is not in use for a
long time (more than 3 months).
• If you have any problems with this device, such as
setting up, maintaining or using, please
contact the manufacturer’s service personnel. Also,
please report to the manufacturer if any unexpected
operation or events occur.
• Do not use the equipment if you notice a change in the
system's performance, if the system is damaged, or if
any of its components are worn or frayed.
• The equipment should not be used adjacent to or
stacked with other equipment. If adjacent or stacked
use is necessary, the equipment should be observed to
verify normal operation in the configuration in which it
is used.
Babysense
monitors and alerts, but cannot prevent any
type of distress. The responsibility for applying first aid
rests on caretakers. The Babysense senses movements and
motion only, and cannot monitor other occurrences. The
purpose of the device is to alert when stopping or slowing
of movement occurs.
Babysense is a unique safety and reassurance system
which helps give parents peace of mind, alerting if
movements stop or become irregularly slow, giving critical
time to intervene. There are a number of cautionary steps,
which are internationally recommended for
SAFE
SLEEPING
:
Babysense
continually detects baby's motion and
movements, and will set off a sound and visual alarm if
movement stops for 20 seconds or if the monitor detects
less then 10 micro-movements per minute. The system's
non-touch sensor pads under the mattress monitor
baby's movement without restraining him.
1.
For inserting the batteries, remove the battery cover
by inserting a wide flat screw driver into the opening
recess (see illustration 6). insert,
in accordance with the
markings
, 4 new and identical size AA 1.5 volt batteries,
preferably alkaline and close cover.
Note:
Please dispose of used batteries in accordance
with local waste regulations.
2.
Place control unit holder on the base of the crib or
bed and in between two bars as shown in illustration 1.
3. Sensor pad installation:
• When using for infant not yet able to crawl, place one
sensor pad as shown in illustration 2. Make sure the
sensor is placed underneath baby’s location in crib.
• When baby begins to crawl, and is able to move onto
areas not "covered" by a single sensor pad, attach the
second sensor and place the two sensors as shown in
illustration 2.
PLEASE NOTE:
The sensors shall be placed with the
marking “THIS SIDE UP” facing upfront.
* Always lay baby to sleep on his or her back.
* Refrain from smoking near or around baby.
* Avoid over-heating of baby's surrounding.
* Do not leave any objects near your baby that can
cause suffocation.
Babysense is an addition to these precautions.
Babysense 7 is a home movement monitor for infants up
to one year of age, and is not to be used with high-risk
infants requiring constant medical supervision. Medically
trained staff such as nurses, or non-medically trained users
such as parents or caregivers may use the Babysense.
Babysense 7 is intended for home use.
Warnings
Principal Of Operation
Installation
Please note
7
The original non-contact baby movement monitor
Now with enhanced sensitivity
I
llustration 1
Control unit holder
User Guide