Baby Love URBANLITE SH608 Series Instruction Book Download Page 29 | Manualshive

Page: 29 / 44

background image

www.babylove.com.au

29

15. SECURING YOUR CHILD IN THE
HARNESS

H

The stroller seat has 3 sets of harness slots at diﬀerent heights to

accommodate the child. To change the shoulder harness height, push
the shoulder harness tongue out of the current harness slot and
through the back of the seat.

I

To reposition harness, pull the shoulder harness buckle tongue

through the desired slot.

«
...
27
28
29
30
31
...
»

Summary of Contents for URBANLITE SH608 Series













































Reviews:

No comments

Related manuals for URBANLITE SH608 Series

Brand: EasyIO Pages: 17

Brand: mikroElektronika Pages: 3

Brand: Window Master Pages: 7

Brand: Case IH Pages: 81

Brand: bluelab Pages: 39

TITAN CONTROLS KRONUS 2

Brand: Sunlight Supply Pages: 4

Brand: GIESSE Pages: 136

Brand: cam Pages: 52

Brand: Progres Pages: 2

Brand: Inca Pages: 11

Brand: Blucave Pages: 2

Brand: WAGO Pages: 2

Brand: Freescale Semiconductor Pages: 41

Brand: Magnimage Pages: 31

Brand: Licht-Technik Pages: 13

Brand: HANYOUNG NUX Pages: 2

Brand: Stahl Pages: 15

Brand: Genius Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands