Baby Love URBANLITE SH608 Series Instruction Book Download Page 22 | Manualshive

Page: 22 / 44

background image

www.babylove.com.au

22

11. ADJUSTING THE BACKREST

A

To raise the backrest, grasp the plastic rings ﬁxed to the adjuster straps

and with the other hand push the backrest up to the desired position.

B

To lower the backrest, support the backrest with one hand and with

the other hand pull down the on the backrest adjuster button and
lower the backrest to the desired position.

«
...
20
21
22
23
24
...
»

Summary of Contents for URBANLITE SH608 Series













































Reviews:

No comments

Related manuals for URBANLITE SH608 Series

Brand: ABB Pages: 2

Brand: Faulhaber Pages: 66

1020 CAN-RS232-RS422 MFL

Brand: PENKO Pages: 29

Brand: Edwards & Co Pages: 16

Brand: Infasecure Pages: 24

Brand: Zennio Pages: 2

Brand: Badger Meter Pages: 66

Brand: cam Pages: 52

Brand: Progres Pages: 2

Brand: Instrutech Pages: 34

New Focus Picomotor 8742

Brand: Newport Pages: 102

Brand: Veris Industries Pages: 4

Brand: Kolcraft Pages: 7

Brand: MDT Technologies Pages: 84

Brand: NEC Pages: 46

Brand: NHRC Pages: 104

Brand: Grundfos Pages: 348

Stauna Controller

Brand: Oceanic Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands