Baby Love URBANLITE SH608 Series Instruction Book Download Page 34 | Manualshive

Page: 34 / 44

background image

www.babylove.com.au

34

• TO AVOID INJURY: BEND YOU KNEES WHEN OPENING, LIFTING,
CARRYING, FOLDING, UNFOLDING OR ADJUSTING THE STROLLER
OR ANY ACCESSORIES.

IMPORTANT NOTES:

PLEASE REFER TO PAGE 4 FOR LIFTING TECHNIQUES.

A

Ensure the storage latch is locked onto the frame before lifting the
stroller. To lift the stroller, grasp the frame halfway along the stroller,
so the stroller is balanced.

19. LIFTING AND CARRYING THE
STROLLER

«
...
32
33
34
35
36
...
»

Summary of Contents for URBANLITE SH608 Series













































Reviews:

No comments

Related manuals for URBANLITE SH608 Series

Brand: 3Ware Pages: 2

Brand: YOKOGAWA Pages: 2

ALICAT SCIENTIFIC PC

Brand: Halma Pages: 2

ALICAT SCIENTIFIC PCD

Brand: Halma Pages: 46

Brand: Taco Electronic Solutions Pages: 28

Brand: V2 Pages: 12

Brand: z21 Pages: 2

Brand: Full Gauge Controls Pages: 3

Brand: Daihan Scientific Pages: 11

Brand: micro-trak Pages: 44

Brand: AUMA Pages: 24

Brand: Contemporary Research Pages: 22

RSF-B mini Series

Brand: Harmonic Drive Pages: 32

Brand: Zander Aachen Pages: 75

Brand: Danfoss Pages: 20

Automation PC 810

Brand: B&R Pages: 428

MotorController WCC 310

Brand: Window Master Pages: 19

LS-RGB-DMX CONTROL

Brand: JBSYSTEMS Light Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands