Baader Planetarium Steeldrive II Technical Documentation Manual Download Page 6 | Manualshive

Page: 6 / 32

background image

Chapter 2

Standalone handheld usage

The SteelDrive focuser may be used standalone (without connection ot another PC). The functions
available in standalone mode are:

•

Continuous focuser movement.

•

Focuser jogging movement.

•

Single step movement.

•

Homing/Zeroing

•

Save outer limit.

•

Save focus position.

•

Goto saved focuser position.

•

Toggle automatic temperature compensation.

•

No limits mode.

2.1

Keypad

The SteelDrive focuser features 4 back-illuminated buttons and two status LEDs (see figure

5

«
...
4
5
6
7
8
...
»

Summary of Contents for Steeldrive II

































Reviews:

No comments

Related manuals for Steeldrive II

Brand: Tailfin Pages: 4

Brand: Vega Pages: 76

Brand: Ranger design Pages: 6

Brand: RAKINDA Pages: 20

Brand: ZALMAN Pages: 20

Brand: Laser Pages: 8

ThermoSensor Clamp

Brand: LaserLiner Pages: 44

Brand: Navibe Pages: 8

Brand: Sanitas Pages: 52

Brand: FABBRI PORTATUTTO Pages: 2

Brand: Yescom Pages: 4

Brand: Z Automotive Pages: 16

Brand: Stramatel Pages: 10

Brand: Yakima Pages: 11

Brand: TAKARA Pages: 2

Brand: Ozeanos Pages: 8

Brand: Boyo Pages: 9

Brand: Whispbar Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands