B.O.B COZ Owner'S Manual Download Page 31

YAK Wheel - 

Monthly, or more often if you ride daily or off

road, inspect your trailer’s wheel. Lift the trailer and spin
the wheel slowly. Check to make certain the wheel does not
wobble side to side. Stop the wheel and check to make sure
all the spokes are tight. The spokes in the wheel have left
and right sides and you will see spokes on the same side
crossing one another. Above the point where the spokes
cross, grab the two spokes and try to squeeze them togeth-
er. The spoke should be tight and resist squeezing.
If the wheel wobbles from side to side or the spokes are
loose the wheel will need to be trued (straightened). This is
a job for a trained bicycle mechanic. It requires special tools
and knowledge.

COZ Axle Nuts -

It is important that your wheel’s axle nuts

remain tight. Please refer to the COZ Wheel Installation
section for proper quick release adjustment and tightening
instructions.

YAK Wheel Quick Release -

It is important that your

wheel’s quick release remains tight. Please refer to the YAK
Wheel Installation section for proper quick release adjust-
ment and tightening instructions.

29

Limited Warranty

B.O.B. Trailers, Inc. warrants original parts of B.O.B trail-
ers products to be free from defects in materials and work-
manship subject to the following conditions and limita-
tions:

Frame is warranted for life of the product.

Components are warranted for one year.

Warranty is only valid for the original purchaser.

Proof of purchase is required to exercise this warranty.

Labor and transportation are not included.

Normal wear, neglect, abuse, accidents, improper
assembly or maintenance, or the installation of parts or
accessories not compatible with the original intended
use of the trailer, as sold, are not covered by this 
warranty.

Warranty claims must be made through an authorized
dealer.

This warranty is limited to the replacement of the
defective part at no cost. B.O.B Trailers shall in no
event be responsible for consequential or special 
damages.

This Limited Warranty is the only express or implied
warranty applicable to B.O.B. Trailers. Any implied
warranties, including warranties of merchanability and
fitness shall be limited in scope and duration in accor-
dance with this limited warranty.

Summary of Contents for COZ





































Reviews: