B+K precision 4040DDS Operating Manual Download Page 2

Model 4040DDS– Operating Manual

2

Limited Two-Year Warranty

B&K Precision warrants to the original purchaser that its products and the component parts thereof,
will be free from defects in workmanship and materials for a period of two years from date of
purchase from an authorized B&K Precision distributor.

B&K Precision will, without charge, repair or replace, at its option, defective product or component
parts. Returned product must be accompanied by proof of the purchase date in the form of a sales
receipt.

To obtain warranty coverage in the U.S.A., this product must be registered by completing the warranty
registration form on www.bkprecision.com within fifteen (15) days of purchase.

Exclusions: This warranty does not apply in the event of misuse or abuse of the product or as
a result of unauthorized alterations or repairs. The warranty is void if the serial number is
altered, defaced or removed.

B&K Precision shall not be liable for any consequential damages, including without limitation damages
resulting from loss of use. Some states do not allow limitations of incidental or consequential
damages. So the above limitation or exclusion may not apply to you.

This warranty gives you specific rights and you may have other rights, which vary from state-to-state.

Service Information

Warranty Service:

Please go to our website,

www.bkpreicsion.com

& click on the service/repair button to

obtain an RMA #. Return the product in the original packaging with proof of purchase to the address below.
Clearly state in writing the performance problem and return any leads, probes, connectors and accessories that
you are using with the device.

Non-Warranty Service:

Please go to our website,

www.bkpreicsion.com

& click on the service/repair button to

obtain an RMA #. Return the product in the original packaging to the address below. Clearly state in writing the
performance problem and return any leads, probes, connectors and accessories that you are using with the
device. Customers not on open account must include payment in the form of a money order or credit card. For
the most current repair charges please visit

www.bkprecision.com

and click on “service/repair”.

Return all merchandise to B&K Precision Corp. with pre-paid shipping. The flat-rate repair charge for Non-
Warranty Service does not include return shipping. Return shipping to locations in North American is included
for Warranty Service. For overnight shipments and non-North American shipping fees please contact B&K
Precision Corp.

B&K Precision
22820 Savi Ranch Parkway
Yorba Linda, CA 92887
www.bkprecision.com
714-921-9095

Include with the returned instrument your complete return shipping address, contact name,
phone number and description of problem.

Summary of Contents for 4040DDS

















Reviews: