manualshive.com logo in svg

B+K precision 4040DDS, Operating Manual, Page: 15 / 16

Share
Download
B+K precision 4040DDS Operating Manual Download Page 15

15

3.6.5 MODULATION Key

Selects the Modulation mode

AM

or

FM

.

To select the output mode, press MODUL key. Each additional operation selects the AM, FM or OFF mode:

AM Menu

The AM depth, from 0% to 100%, is changed with the rotary knob.

FM Menu

The FM deviation frequency is changed with the rotary knob.

3.6.6 COUNTER Key

By pressing this key, the build-in Frequency counter is enabled and the frequency of the signal connected to the

TRIG IN connector is displayed. The counter is auto ranging with up to 8 digits resolution.

Counter Menu

3.7 Cursor Movement Keys

Use these keys to move the cursor (when visible) either left or right. They are used in conjunction with the rotary input
knob to set the step size of the rotary input knob.

3.8 Rotary Input Knob

Use this knob to increase and decrease numeric values or to scroll through a list. The cursor indicates the low-order

position of the displayed value which changes when you rotate the knob (for straight numeric entries only). For other
types of data, the whole value changes when you rotate the knob.

Summary of Contents for 4040DDS

















Reviews:

No comments