background image

RELEASED 

7-13-12

REFERENCE

 

NUMBER

INS000002

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY 
DESCRIBE.  REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

5/64” allen wrench

Warning

High Voltage

Hot Surface

NEEDED

FOR 

INSTALLATION:

By Others

LED BOARD/DRIVER/OPTICS

1 5/8” Body Size

Standard Installation/Replacement 

Re-placing LED Board/Driver and Optics

1.   Use 5/64” Allen wrench to loosen #8-32 stainless set 

screw and remove cap. 

2.   Space three fingers evenly around the optic and 

gently rock optic to remove.  

4.   Disengage LED board and driver assembly. Replace 

with new board and driver assembly.  

5.   Reverse install LED board and driver by carefully 

wrapping 18 gauge wires around driver and 
inserting into fixture body. Secure LED board in 
place with stainless steel screws. 

6.  Snap optics in place. Place cap on fixture and 

tighten set screw.

3.  Use 5/64” Allen wrench to remove two (2) #2-56 

socket head cap screws on LED board, grasp LED 
board and gently pull up to expose quick disconnect. 

• 

Product must be installed by a qualified person in a manner 

consistent with its intended use and in compliance with the 
National Electrical Code, Canadian Electrical Code, and all Local 
and Provincial Codes. 

• 

Follow product label information and instructions.

• 

Qualified Personnel must perform all servicing or relamping of 

this product.

• 

Before wiring to power supply and during servicing or relamping, 

turn off power at fuse or circuit breaker before service.

• 

The use of accessory equipment not recommended by the 

manufacturer or installed contrary to instructions may cause an 
unsafe condition. The use of damaged components may cause 
an unsafe condition and void product warranty.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY 

AND INSTALLATION INSTRUCTIONS

• 

Do not block light emanating from product in whole or part, 

as this may cause an unsafe condition.

• 

Never operate the fixture with missing or damaged lens. 

Lens must be cleaned on regular basis.

• 

Entire fixture may become extremely hot. Do not touch hot 

lens or fixture body. Do not touch the lamp at any time. Use 
a clean, dry, soft cloth to handle the lamp. Oil from skin may 
damage the lamp and cause it to rupture.

• 

Replace lamp only with correct wattage and type of lamp 

marked on fixture label.

• 

All gaskets, o-rings and sealing surfaces must be kept clean 

during installation and service; failure to do this may cause an 
unsafe condition and void product warranty. 

INSTRUCTIONS PERTAINING TO 

A RISK OF FIRE, OR INJURY TO 

PERSONS IMPORTANT SAFETY 

INSTRUCTIONS

Lighted lamp is HOT!

WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS: 

Turn off/unplug and allow to cool before replacing lamp. 

Lamp gets HOT quickly! Contact only switch/plug when 

turning on. 

Do not touch hot lens, guard, or enclosure (see diagram/

picture). 

Keep lamp away from materials that may burn. 

Do no touch the lamp at any time. Use a soft cloth. Oil 

from skin may damage lamp. 

Do not operate the luminaire fitting with a missing or 

damaged shield.  

SAVE THESE INSTRUCTIONS

Reviews: