B+B SmartWorx IE-MultiWay User Manual Download Page 20

Page: 20 / 66

-MultiWay

Command

Description

cleandb

Reboots the unit with a clean database. This removes all information

from the database and sets the unit to factory defaults.

download

Downloads firmware via the TFTP protocol

accounts

Allows the addition for User, Superuser, Admin

vlan

Provides selection of two modes of operation to support all VLAN

configurations.

Displays settings for Bandwidth configuration

mactab

Displays MAC tables

ifstats

Displays interface statistics

rmstats

Displays remote monitoring (RMON) statistics on packets received as

defined in RFC 2819 for RMON.

sysDescr

Allows the editing of sysName, sysDescr, and Port information

reboot

Allows a soft reboot of the unit after changes are made by the end

user

oam

Enable/disable OAM

sfpstats

Provides information about the wavelength, serial number, output

power, BER and other information. Requires an SFP with DDMI.

unit

Unit global settings, frame size selection. Unit OAM enable must be

enabled for AH and AG to function.

port

Displays the port status and allows changes to port settings, such as

duplex status and speed.

CLEANDB

Entering cleandb reboots the unit with its database cleaned depending on the option

selected. Users are presented with two, sequential options, first to reset all SNMP settings

and, second, to reset all of the units configuration to default. Enabling the first option

presents the second. Resetting the unit to factory default values (option two) will delete all

custom IP and other configurations performed through iView².

Summary of Contents for IE-MultiWay



































































Search results

Summary of Contents for IE-MultiWay

Reviews:

Related manuals for IE-MultiWay

Brands by name

Popular brands

B+B SmartWorx IE-MultiWay, User Manual

Search results

Summary of Contents for IE-MultiWay

Reviews:

Related manuals for IE-MultiWay

Brands by name

Popular brands