Axxess AXDIS-CL2 Installation Instructions Manual Download

Page: 12 / 12

AxxessInterfaces.com

REV. 1/21/20 INSTAXDIS-CL2

I N S TA L L AT I O N I N S T R U C T I O N S

AXDIS-CL2

NOWLEDGE IS

OWER

nhance your installation and fabrication skills by

enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.

Metra recommends MECP
certified technicians

Having difficulties? We’re here to help.

Contact our Tech Support line at:

386-257-1187

Or via email at:

[email protected]

Tech Support Hours (Eastern Standard Time)

Monday - Friday: 9:00 AM - 7:00 PM
Saturday: 10:00 AM - 7:00 PM
Sunday: 10:00 AM - 4:00 PM

Resetting the AXDIS-CL2

The

Blue

reset button is located inside the interface, between the two connectors. The button is accessible outside the

interface, no need to open the interface.

Press and hold the reset button for two seconds, and then let go to reset the interface.

Refer to “Programming the Interface” from this point.

Dual assignment legend

1.  Not allowed
2.  Not allowed
3.  Seek-Up/Next

4. Seek-Down/

5. Mode/Source
6. ATT/Mute

7.  Preset-Up
8.  Preset-Down
9.  Power

10.  Band
11.  Play/Enter
12.  PTT

13.  On-Hook
14.  Off-Hook
15.  Fan-Up *

16.  Fan-Down *
17.  Temp-Up *
18.  Temp-Down *

* Not applicable in this application

STEERING WHEEL CONTROL SETTINGS

(CONT)

TROUBLESHOOTING

Summary of Contents for AXDIS-CL2













Search results

Summary of Contents for AXDIS-CL2

Reviews:

Related manuals for AXDIS-CL2

Brands by name

Popular brands

Axxess AXDIS-CL2, Installation Instructions Manual

Search results

Summary of Contents for AXDIS-CL2

Reviews:

Related manuals for AXDIS-CL2

Brands by name

Popular brands