background image

06

Specifications

Axminster No. 

(100081) AW12BM

Rating: 

Light Trade

Motor:  

240V a.c. 50 Hz 370W

Chisel Stroke: 

110mm

Centre of Chisel to Back Fence: 

95mm

Max Height of Timber with 12.7mm Chisel and Bit: 

120mm

Max Chisel Size Softwood: 

12.7mm

Max Chisel Size Hardwood: 

12.7mm

Overall L x W x H: 

350 x 350 x 600mm

Weight                                                                             

25kg 

Initial Assembly of the Machine  (Continued)

2) Locate the Accessory tray, the small ‘P’ clip and the three small panhead screws. Locate the 3

No. threaded holes in the rear upper left side of the headbox. Snap the ‘P’ clip on the cable, tidy’
the mains cable away from the front of the machine, and secure into the most forward threaded
hole. Offer up the accessory tray and secure using the remaining two panhead screws, into the
threaded holes. 

3) Locate the backfence and its associated components. Fit the lift and shift clamping handle into
the back fence mounting block, leave the housing clear to fit the main mounting bar of the back
fence. Fit the large spring over the main mounting bar, introduce the bar into the mounting block
and push home, put the spring under some tension and tighten down the clamping handle.
Located the ‘fine adjust’ assembly over the main bar and secure in place by tightening the socket
grubscrew. Turn the adjusting bolt until the bolt is in contact with the mounting block. Unlocking
the clamping lever handle should enable the back fence to be adjusted back and forth using the
adjusting bolt ‘with’ or  ‘against’  the tension in the spring. 

4) Locate the handle and the grip sleeve, fit the sleeve over the handle. (If it is difficult to slide on,
try lubricating with a small amount of washing up liquid. Locate the small spring and the large
headed screw. Place the handle over the rise and fall shaft, fit the spring over the large head
screw shaft and screw into the end of the rise and fall shaft. The spring pressure should be
enough to keep the castellated dogs of the handle and the rise and fall shaft together under
normal operation, but allow the dogs to be disengaged to re-position the handle. Exercise the
headbox up and down and check everything works satisfactorily.

5) Locate the hold down yoke, fit over the rod fitted upright in the backfence casting,
secure in place using the  socket grubscrew.  Locate the dust extraction pipe and the short 
caphead bolt. The pipe is located onto the hold down yoke using the bolt into a pre-threaded
hole in the top of the left arm of the hold down yoke.

Summary of Contents for AW12BM





















Reviews: