Axminster 100247 User Manual Download Page 2

Page: 2 / 24

The Axminster Skill Centre is based within the Axminster Tool Centre retail
store and is fitted out with an extensive range of tools and machinery. Our
courses are run by experienced tutors who offer students a wealth of
knowledge, experience and enthusiasm. For full details of our increased
range of courses and availability, contact us on

0800 9751905

alternatively visit our website

www.axminsterskillcentre.co.uk

Index of Contents...

Page No.

Safety Protection Symbols

SAFETY!!

The symbols shown on the cover of this
manual advise you to observe the appropriate
safety protocols when using this machine.

e P

rotectio

fet

y Helm

ctive Glov

ty F

ootw

spirator

fety Visor

d Manua

n Assem

r D

efende

st Mask

Index of Contents..................................................................................................................02

What’s in the Box………….………........……..………….........................................................03

Optional Accessories............................................................................................................04

Basic Safety for Machine Tools.......................................................................................05-06

Specific Safety Instructions for the Chuck...........................................................................06

Four Jaw Self Centring Chuck..............................................................................................07

Changing the Chuck Jaws.....................................................................08-09-10-11-12-13-14

Woodturning Chuck Jaws...................................................................... 15-16-17-18-19-20-21

Chuck Accessories.....................................................................................................20-21-22

Maintenance...........................................................................................................22

Lathe Thread Information.....................................................................................................23

Parts Breakdown...................................................................................................................23

Right & Left Hand Threads Table..........................................................................Back Cover

Summary of Contents for 100247

























Search results

Summary of Contents for 100247

Reviews:

Brands by name

Popular brands

Axminster 100247, User Manual

Search results

Summary of Contents for 100247

Reviews:

Brands by name

Popular brands