Axminster Craft AC82E Original Instructions Manual Download Page 10 | Manualshive

Page: 10 / 20

background image

Assembly

10

18

22

20

21

19

Use the polystyrene packing to support the extractor (A)
when mounting the base assembly the opposite way round.

Lower the filter bag hanger bar (E) down into the mounting
bar (F), see step 22.

F

E

Mounting bar (F)

A

C

Polystyrene

Remove screws

Hex (K)

Screw the hanger

mounting bar (F)

into the extractor

assembly (A)

Tighten the

nut to lock the

mounting bar

(F) in place

«
...
8
9
10
11
12
...
»

Summary of Contents for AC82E





















Reviews:

No comments

Related manuals for AC82E

Brand: Unitekno Pages: 52

Brand: Grundig Pages: 9

Brand: HART Pages: 24

Brand: Nilfisk-ALTO Pages: 15

Brand: Infinity Pages: 2

Cordless Blade Pet Slimvac VX66

Brand: Vax Pages: 13

Brand: V. BRØNDUM A/S Pages: 51

Brand: Hanseatic Pages: 61

Brand: Black+Decker Pages: 20

Rapide Classic V-024

Brand: Vax Pages: 8

Brand: RIDGID Pages: 48

Brand: Electrolux Pages: 28

Brand: Electrolux Pages: 48

Enviro Multi Steamer Plus

Brand: Electrolux Pages: 11

Brand: Electrolux Pages: 28

Brand: Electrolux Pages: 7

Brand: Frigidaire Pages: 14

Brand: Frigidaire Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands