background image

Main Heading

2

EU Declaration of Conformity

Fully read manual

and safety instructions

before use

Eye protection

should be worn

Ear protection

should be worn

HAZARD

Motor gets hot

Dust mask

should be worn

The symbols below advise the correct safety procedures when using this machine.

Cert No:  FM230L3

Axminster Tools & Machinery Ltd
Axminster Devon 
EX13 5PH UK
axminster.co.uk

Type

Dust Extractor

Model

AC82E

and conforms to the machinery example for which the 
EC Type-Examination Certificate No AE 50352798, AE 50389324, AE 50398634  
has been issued by Laizhou Planet Machinery Co., Ltd.
at:  Yutai West Street Laizhou, Shandong 261400 China

and complies with the relevant essential health and safety requirements. 

2006/42/EC
2014/30EU
06/42/EC - Annex I/05.2006 
EN 62233:2008 

declares that the machinery described:-

This machine complies with the following directives:

EU Declaration of Conformity

EN 60335-2-69:2012 
EN 60335-1:2012+A11

Signed

Andrew Parkhouse
Operations Director

Date: 08/08/2016 

EU Declaration of Conformity 

02

What’s Included 

03-04

Optional Accessories 

04

Introduction 05
General Instructions for 230V Machines 

05

Specific Safety for Dust Extractors 

06

Specification 06
Assembly 07-08-09-10-11-12
Illustration and Parts Description 

13-14

Operating Instructions 

15

Maintenance 16
Exploded Diagrams/Lists 

17-18

Wiring Diagram 

19

Summary of Contents for AC82E





















Reviews: