Axis AX-824RHD Manual Download Page 20

20

TROUBLESHOOTING

PROBLEM

CHECK

ACTION

The oven is completely OFF.
There is no water coming 
from solenoid.

Safety thermostat

Requires service technician for 
repair

Water inlet is closed

.

Open water inlet valve

Incorrect connection to water 

Check connection to water supply

Loose light bulb

Correctly fit bulb in socket

Light does not work

Light bulb is burnt

Replace light bulb

Non-uniform cooking

Fan(s) no longer invert rotation
during cooking

Requires service technician for 
repair

One of the fans is not 
working

Requires service technician for 
repair

Non-uniform cooking
The oven is completely OFF

Heating element is defective

Requires service technician for 
repair

Supply voltage inadequate

Check breaker or fuse

Incorrect connection to 
power supply network

Check connection to power supply

There is no water inflow 
from the humidifier pipes 
Water leaking from the 
gaskets with the door open 

Water filter is blocked with
impurities

Clean filter

Dirty lining

Clean lining with damp cloth

Damaged Gasket

Replace gasket

Water leaking from the 
gaskets with the door open 
The fan stops while the oven 
is on 

Door does not close properly

Verify door mechanism

Safety Thermostat or 
motor may be defective

Turn off the oven and wait for the 
motor's thermal protection to reset 
itself. If the problem persists call a 
specialised repair technician 

Motor Capacitor defective

Requires service technician for 
repair

Summary of Contents for AX-824RHD






















Reviews: