background image

SBC8168 Socket 370 All-in-One CPU Card Series User’s Manual 

 

Display Drivers 

23

C h a p t e r  5 

Display Drivers 

5.1 Introduction 

The Intel 815 GMCH includes a highly integrated graphics 
accelerator. Its architecture consists of dedicated multi-media 
engines executing in paralle to deliver high performance 3D, 
2D, and motion compensation video capabilities. The 3D and 
2D engines are managed by a 3D/2D pipeline preprocessor 
allowing a sustained flow of graphics data to be rendered and 
displayed. The deeply pipelined 3D accelerator engine 
provides 3D quality graphics and performance via per-pixel 3D 
renderign and parallel data paths which allow each pipeline 
stage to simultaneously operate on different primitives or 
portions of the same primitive. The Intel 815 GMCH graphics 
accelerator engine supports perspective-correct texture 
mapping, trilinear and anisotropic Mip-Map filtering, Gouraund 
shading, alpha-blending, fogging and Z-buffering. A rich set of 
3D instructions permits these features to be independently 
enabled or disabled. 

5.2 Features 

 

z

 

AGP interface controller with onboard 4MB SDRAM 
(optional) 

z

 

Supports CRT displays 

z

 

Display memory supports up to 1600x1200 8 bit-color 
resolution on non-interlaced CRT monitors 

z

 

3D Hyper Pipelined architecture 

z

 

Full 2D H/W Acceleration 

z

 

Motion Video Acceleration 

Summary of Contents for SBC8168









































































Reviews: