background image

 

 

 

 

General Safety Summary 

Carefully read the following safety precautions to avoid person injury and prevent damage to the 
instrument and any products connected to it. To avoid potential hazards, please use the instrument as 
specified. 

Only qualified technician should perform service procedures 

To Avoid Fire or Personal Injure 

Use Proper Power Line 

Use only the special power line of the instrument which approved by local state. 

Ground the Instrument 

The instrument grounds through the protective terra conductor of the power line. To avoid electric 
shock, the ground conductor must be connected to the earth. Make sure the instrument is grounded 
correctly before connect its input or output terminals. 

Connect the Signal Wire Correctly 

The potential of the signal wire is equal to the earth, so do not connect the signal wire to a high 
voltage. Do not touch the exposed contacts or components. 

Look Over All Terminals’ Ratings 

To avoid fire or electric shock, please look over all ratings and sign instruction of the instrument. 
Before connecting the instrument, please read the manual carefully to gain more information about the 
ratings. 

Not Operate with Suspected Failures 

If you suspect that there is a damage of the instrument, please let a qualified service personnel check 
it. 

Avoid Circuit or Wire Exposed Components Exposed 

Do not touch exposed contacts or components when the power is on. 

Do not operate in wet/damp conditions. 

Do not operate in an explosive atmosphere. 

Summary of Contents for AX-DG2010AF














Reviews: