CMD-5xx 08/07/02
4
Standard Configurations
Board
Processor
Board
Processor
Board
Processor
CMD-555
MPC555
CMD-562
MPC562
CMD-565
MPC565
CMD-556
MPC556
CMD-563
MPC563
CMD-566
MPC566
CMD-561
MPC-561
CMD-564
MPC564
CMD-560
MGT560
Example part number: CMD-565 would be the CMD-5xx board with the PM-565 Personality Module that has a
socketed processor, AMD flash, and the global power source.
CMD-5xx Features
•
Standard fixed memory (buffered):
•
512K x 32 Sync. SRAM (100MHz)
•
1M x 32 Burstable Flash EPROM
•
Two Configurable 32pin memory sockets for 32K to 2MByte EPROM with 8 or 16 bit wide data bus, Axiom Monitor
installed standard.
•
PRU - Port Replacement Unit provided for MPC5xx ports A, C, and D allow simulation of single chip port operation when
expanded bus is operating.
•
MAP Switch – provides easy assignment of chip selects to ram and flash memory banks.
•
MODE Switches – 4 DIP switches to fully support Hard Reset Word Configuration options.
•
COM Switch – provide easy method of applying or isolating serial connections to RS232 transceiver.
•
COM1 - SCIA1 w/ RS232 type DB9-S Connection
•
COM2 - SCIA2 w/ RS232 type DB9-S Connection
•
COM3 – SCIB1 w/ RS232 type 10pin cable Connection
•
COM4 – SCIB2 w/ RS232 type 10pin cable Connection
•
CAN Ports – 3 CAN transceiver (PCA82C250) interfaced ports, 1 x 4 headers.
•
LCD Port - LCD Module Interface Connector w/ Contrast Adjust, Buffered and Memory Mapped
•
KEYPAD and KEY Port - 16 Key or 20 Key interface, Debounced, Buffered, and Memory Mapped
•
BUS Port – provides 32 data and 24 address or MPC5xx ports A and D on 60 pin header.
•
CONTROL Port - Bus Controls or MPC5xx ports on a 44 pin header.
•
QSM Ports – 2 Serial I/O ports with 16 pin socket headers.
•
MIOS Port - MDA, PWM, and MGP timer or I/O interface with 34 pin socket header.
•
TPU Ports - 3 Timing Processor I/O ports with 20 pin socket headers.
•
QADC Ports - 2 Analog I/O ports, one 20 pin and one 24 pin socket header.
•
INT Port – Interrupt or MPC5xx SGP port I/O with 10 pin header.
•
POWER Port – Primary and standby power supply access port.
•
I/O Connectors in .1 grid, pin headers for bus and control provide easy ribbon cable connection for external connections.
Socket headers provide easy wire connection to solderless prototype area or with provided pin headers installed, will allow
ribbon cable or wire wrap connections.
•
Large Prototyping Area (5 x 1.75 inch) with +5V and ground connection grids.
•
Mictor Logic Probe connectors for the Address and Data bus
•
Solderless Prototyping area (2.5 x 1.5 inch) for easy installation of test connections.
•
Power Indicators – Supply voltage indications for 5, 3.3, and 2.6V supplies
•
Reset Switches – POR, Hard, Soft reset buttons.
•
User Indicators – 4 user indicators to provide user conceived visual response during testing.
Axiom development systems provide for low cost software testing with the use of the Monitor in the on-board EPROM. Operation
allows the user to load code in the On-Board RAM, Execute application, and display or modify registers or memory. After code is
operational the user may relocate the code and reprogram the MPC5xx Internal Flash EEPROM or the boards fixed flash for
dedicated operation of new software. No additional hardware or software is required to operate. For high level debug, extensive
tools are available for the PowerPC core and the Debug Port is available on the PM-5xx module to connect a background debugger.
