axing MIE 16-00 Manual Download Page 6

Page: 6 / 39

•

Mounting and Installation

•

Installation must be performed by authorized and skilled electricians only.

•

Before mounting and installation, pull the mains plug!

•

The DVB-C/T distribution network must be installed and connected to the equipotential bonding according to EN 60728-

11.

•

Install the device in compliance with the safety regulations defined by the EN 60728-11 standard.

•

Mounting in a 19“ rack

Note:

For 19-inch rack mounting, there must be at least 5 cm clearance in front of and behind the unit.

•

Slide the device into the 19 "rack.

•

Screw the device with four screws (2).

•

Install the device in compliance with the safety regulations defined by the EN 60728-11 standard.

•

Equipotential bonding

•

The device must be connected to the equipotential bonding according to EN 60728-11. Use the equipotential bonding

connection at the device.

•

To connect the outer conductor of the coaxial cable to the equipotential bonding, use e.g. QEW earthing angles or CFA

earth connection blocks at the inputs and output.

Summary of Contents for MIE 16-00








































Search results

Summary of Contents for MIE 16-00

Reviews:

Related manuals for MIE 16-00

Brands by name

Popular brands

axing MIE 16-00, Manual

Search results

Summary of Contents for MIE 16-00

Reviews:

Related manuals for MIE 16-00

Brands by name

Popular brands