background image

System Setting

In system setting menu, you can modify operation and
display setting, such as dome label, temperature and
display of various value on the operational screen.

EDIT DOME LABEL

LABEL

BACK

EXIT

ENTRANCE

INITIAL  INFO

SPEED DOME V1.00
PROTOCOL:FACTORY
DOME ADDRESS:001
COMM:4800,N,8,1
BACK
EXIT

6.OSD - System Setting

6.OSD - Motion, Clear

Initial information:

Shows the information about current setting.

Dome Label:

1. use UP or DOWN to change the charactor.

2. use RIGHT to move to next char.

3. use RIGHT to move to last char and save.

4. use Left to first char and cancel.

Display setup

Dome label:
Preset label:
Zoom label:
Zone label:
Direction label:

Temperature label:

Actuvate the display for the on-screen info in operaton
mode.

the name of dome

shows the labe of every preset

shows zoom factor on screen

shows the zone name

shows the coordinates

shows the cur. temp in the speed dome

DISPLAY  SETUP

DOME LABEL

OFF

PRESET LABEL

OFF

ZOOM LABEL

ON

ZONE LABEL

OFF

DIRECTION LABEL

ON

LABEL

OFF

BACK

EXIT

TEMPERATURE

Some products may not be available in your country, please contact our distributor for more details

Some products may not be available in your country, please contact our distributor for more details

13

14

SYSTEM  SETTING

EDIT DOME  LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
BACK
EXIT

MOTION

Motion control

AUTO FLIP

PROPORTIONAL PAN:

PARK TIME:

: Auto. Image flip in tilt range from 90° to

180°

depends on the zoom factor,

the dome will adjust the pan and tilt speed
automatically for comfortable viewing.

defines the idle time prior to start a

custom defined action( park action).The range is
from 1 to 240 minutes. This function can be
deactivated by setting the minute to 0.

PARK ACTION:

POWER UP ACTION:

FAN ENABLED:

TEMP C/F:

the action which will be started after

the idle time (park time). Selectable between Preset,
Scan, Pattern (Nr), Tour or None.

defines the action which will

be started after power up and self test. Selectable
between Auto,Preset 1, Scan, Pattern (Nr), Tour or
None. By selecting Auto, the dome will resume the
last action before power off.

Activate Fan when the dome reach the

temperature.

Switch the temperature unit between Celius and

Fahrenheit.

Advance Setting

EIS ENABLED:

E

I

S

PRESET FREEZEN:
AUTO FOCUS:
DEFOGGER:
HEAD UP:

Enable „ lectric mage

tabilization“. This

function is variable on certain camera modul.

Freeze the image immediately.

Switch ON/OFF the Auto Focus

Activate Heater/Fan on the cold temperatur.

Switch ON/OFF the proportional PT moving. Can

combine with Camera Flip function.

AUTO  FLIP

ON

PROPORTION  PAN

ON

PARK TIME

005

PARK ACTION

SCAN

POWER  UP ACTION AUTO
FAN ENABLED              040
TEMP C/F                       CENT
ADVANCE SETTING
BACK
EXIT

Clear

You can clear setting’s memory or reset the camear to
factory default. The follwing functions are supported:

- Clear Zones
- Clear all presets
- Clear all patterns
- Clear all tours
- Clear all windows
- Factory defaults

Warning

:

The clear action can not be undone.

once a item is cleared it is impossible to
retrieve the deleted setting. Please make sure
that the requested clear action is desired.

CLEAR

CLEAR ALL ZONES
CLEAR ALL PRESETS
CLEAR ALL PATTERNS
CLEAR ALL TOURS
CLEAR ALL WINDOWS
FACTORY DEFAULTS
RESTART
BACK
EXIT

ADVANCE SETTING

EIS ENABLED                N/A
PRESET FREEZEN       OFF
AUTO FOCUS                OFF
DEFOGGER                   015C
HEAD UP

OFF

BACK
EXIT

Summary of Contents for High Speed dome Camera Series
















Reviews: