background image

Phone: 1-803.358.3600 • Fax: 1-803.358.3636

100 Innovation Place • Lexington SC 29072 USA

avtecinc.com

[email protected]

d. The

VAGC Max Gain (dB)

field, enter the maximum amount of gain VAGC will apply for receive

audio to remain at or above the

VAGC Low Target (dB)

. Range: 0 to 23 dB. Default: 20 dB.

e. In the

VAGC Threshold (dB)

field, enter the minimum decibel level where VAGC begins to apply gain

to receive audio. Range: –65 to –20 dB. Default: –20 dB.

IMPORTANT

Use caution when setting these fields. Avtec recommends first adjusting the

Windows Input

Level (%)

and

Mic Gain (dB)

fields before attempting to adjust any VAGC setting.

Mic Gain (dB)

adjustments should only be made in small increments.

10. Enter the level the Software Media Workstation outputs audio to the external audio interface in the

Output

Level (dB)

field. Range: –40 to 0 dB. Default: –10 dB.

11. In the

Output Level (dB)

field, enter the level, as a percentage, of the audio coming from the media workstation

to the external audio interface. Range: 0 to 100. Default: 35.

12. Under the

Scout IRR Settings

section, from the

Audio Payload Type

dropdown, select the codec used for

transmitting VoIP audio toward the Scout IRR. Default: G.711.

13. In the

Jitter Delay (ms)

field, enter the amount of time in milliseconds that the Scout IRR should wait before

decoding VoIP packets from this device. Range: 40 to 2500. Default: 60.

14. From the

Voice Activity Detection

dropdown, select whether or not the transmission of VoIP packets toward

the Scout IRR is based on the presence of voice in the audio stream. Default: DISABLED.

15. Click

Update

.

Configuring the Endpoint for NENA Devices

1. From Scout Manager's

Configuration

tab, in the

Endpoints

folder, select

Add New

>

Endpoint

.

2. Right-click the new endpoint that displays under the

Endpoints

folder and select

Properties

(or double-click the

new endpoint).

The

Endpoint Editor

dialog box displays.

3. Configure the endpoint's settings as appropriate. Verify that the

Endpoint Profile

that you assign to this

endpoint is consistent with the way you want the endpoint to operate.

IMPORTANT

This endpoint is considered a "media workstation endpoint" and not a "VPGate endpoint" because the

interface is directly connected to the console through a USB cable, and not through a VPGate. The

Name

you assign to this endpoint should be unique from other VPGate endpoints that are on the same domain.

10

Avtec USB NENA Jack Box Configuration Guide

| October 2021 | Revision 9

Summary of Contents for USB NENA

























Reviews: