Avtec Scout NENA Configuration Manual Download Page 2

Page: 2 / 15

Phone: 1-803.358.3600 • Fax: 1-803.358.3636

100 Innovation Place • Lexington SC 29072 USA

avtecinc.com

•

This document contains proprietary information that is protected by copyright. No

part of this document may be reproduced, stored in a retrieval system, or

transmitted in any form or any means electronic, mechanical, photocopying,

recording or otherwise, without the prior written consent of Avtec, LLC.

Scout™, VPGate™, Outpost™, Outpost Plus™, Frontier™, Audio Bridge™, Avtec SIP

Proxy™, ScoutLink™, DSPatch, DSPatchNET, and CommScape™ are trademarks of

Avtec, LLC. All other brands and their products are trademarks or registered

trademarks of their respective holders and should be noted as such.

The material in this document is for information only and is subject to change

without notice. While reasonable efforts have been made in the preparation of

this document to assure its accuracy, Avtec, LLC assumes no liability resulting from

errors or omissions in this document, or from the use of the information contained

herein. Avtec, LLC reserves the right to make changes in the product design

without reservation and without notification to its users.

Summary of Contents for Scout NENA















