background image

4

 

SPC Installer/User Guide

For configurations that require multiple fully-privileged users, administrative 

privileges may be granted to other users in the system.

Automatic time-out

When an SPC user ends a session, configuration changes made during the 

session are saved. For added system security, a user session will be terminated 

automatically after five minutes of inactivity, without saving any configuration 

changes made during the session. If a user is called away unexpectedly, an 

unprotected channel will not remain open indefinitely.

Configuration reset capability

The SPC may be reset to the factory default configuration through an 

administrative level command. If the administrator password is lost or 

unavailable, the unit may be reset manually by pressing a reset button on the 

SPC unit.

Using the SPC with Avocent Appliances

The SPC user interfaces described in this document are available when a serial 

Telnet connection is made to the unit. When an SPC is connected as a device on 

an Avocent appliance, these interfaces may be available or other interfaces may 

be provided by the Avocent appliance, depending on the configuration. For more 

information, see the installer/user guide for the appropriate Avocent appliance.

Safety Precautions

This section contains important safety and regulatory compliance information that 

should be reviewed before installing and using the SPC. For input and output 

current ratings, see 

Appendix B

.

• 

This equipment is only for installation by qualifi ed service personnel and 
use in a Restricted Access Location with the following installation and 
use instructions.

• 

This equipment is designed to be installed on a dedicated circuit.

• 

The dedicated circuit must have circuit breaker or fuse protection. SPC 
units have been designed without a master circuit breaker or fuse to avoid 
becoming a single point of failure. It is the customer’s responsibility to 
provide adequate protection for the dedicated power circuit. Protection 
should not exceed 120% of the Total Output Rating of the SPC units (see 

Appendix B

), have a 10,000 A interrupt rating and must meet all applicable 

local, state and federal codes and regulations.

• 

The plug on the power supply cord shall be installed near the equipment 
and shall be easily accessible.

Summary of Contents for SPC

























































Reviews: