Avnet 78368 User Manual Download Page 30

Page: 30 / 87

MSC SM2S-IMX8MINI

30 / 87

User Manual

4.3 PCI Express

The i.MX8M Mini SoC supports PCIe x1 Gen2 lane.*

Table 8: PCIe Signal Description

Signal

Pin Type

Signal Level

Pin on
i.MX8M Mini

Pin name on
i.MX8M Mini

Power
Tolerance

PU/PD

Description

PC
PCIE_A_TX-

LVDS PCIe

B20

A20

PCIE_TXN_P

PCIE_TXN_N

According to
PCIe spec

PCI Express Differential Transmit Pairs. AC
coupled on module

PC
PCIE_A_RX-

LVDS PCIe

B19

A19

PCIE_RXN_P

PCIE_RXN_N

According to
PCIe spec

PCI Express Differential Receive Pairs

PCIE_
PCIE_A_REFCK-

LVDS PCIe

B21

A21

PCIE_CLK_N

PCIE_CLK_P

According to
PCIe spec

PCI Express Reference Clock. AC coupled
on module. Clock enabled by default.

PCIE_WAKE#

3.3V CMOS

N27

NAND_RE_B

3.3V

PU 10k

PCI Express Wake signal. Asserted by
device when requesting wake up.

(CPU GPIO3_IO15)

PCIE_A_RST#

O PP

3.3V CMOS

K27

NAND_CLE

3.3V

PCI Express Reset output signal.

NOTE: In case GBE1 Interface is implemented on the module the PCIe Interface will no longer be available. Pins can be left unconnected

4.4 USB

The USB controller supports USB 2.0.

Depending on the module variant the following USB lane options are available:

•

Option 1

with USB 2.0 Hub: USB[0] = USB 2.0 host/device OTG compliant

USB[1:4] = USB 2.0 host

•

Option 2

without USB 2.0 Hub: USB[0] = USB 2.0 host/device OTG compliant

USB[1] = USB 2.0 host.

Summary of Contents for 78368
























































































Search results

Summary of Contents for 78368

Reviews:

Related manuals for 78368

Brands by name

Popular brands

Avnet 78368, User Manual

Search results

Summary of Contents for 78368

Reviews:

Related manuals for 78368

Brands by name

Popular brands