manualshive.com logo in svg

Aviosys IP Power 9258 DS, User Manual, Page: 22 / 37

Share
Download
Aviosys IP Power 9258 DS User Manual Download Page 22

 

 

IP Address: 

The IP Address of the 9258 DS can be specified here. If you are using a hub or 

router, the IP address may be selected for you already. Otherwise you can manually select the IP 
Address here.  

 
Subnet Mask: 

The Subnet Mask Address of the 9258 DS can be specified here. If you are using 

a hub or router, the IP address may be selected for you already. Otherwise you can manually 
select the IP Address here. 
 

Default Gateway: 

The Default Gateway is given by a router or hub and this is where that 

information would be specified. 

 
DNS: 

The DNS is the Domain Name Server. This information can be obtained by contacting the 

ISP  

 
DHCP Client

: The DHCP client allows the 9258 DS to use DHCP to obtain the IP Information 

from a Hub or Router.  
 

Beeper: 

The Beeper turns on/off the beeper sound from the 9258 DS. When commands are sent 

a beep sound will appear 
. 

Http Command Verification:

 The HTTP Verification turns on or off the HTTP Command mode. 

This mode allows you to send commands directly to the device via internet without having to 
enter the device.  
 

Device Name:

 In this section you can change the name of the 9258 DS for easier identification 

purposes. It is also a way to find your device using IP Service. 
 

Release Version: 

Displays information on the Firmware version and release date.  

 

 

- 22 - 

Summary of Contents for IP Power 9258 DS






































Reviews:

No comments