Avio iP-40 User Manual Download Page 15

E-1

A Check of the Supplied Items and the Names of the Parts

Operation of the Remote Control

•  Please use the remote control within a range of about 7 m from the remote control IR sensor of the projector (located at both 

the front and rear) and within an angle of 10 degrees to the left and 10 degrees to the right. Note that this distance may be 
shorter depending on battery consumption.

•  The remote control will not function when there is an obstacle located between the remote control and the remote control IR 

sensor of the projector.

Battery Replacement

1

Insert  the  battery  with  the  +  side  facing  up  as  illus-
trated on the inside of the case.

Firmly  hold  the  remote  control  with  your  hand  and 
insert the tip of a ballpoint pen or some other pointed 
object into the hole on the rear side.
Note that there is the risk of scratching the case when 
using a pointed item such as an awl.

Slide the battery holder toward you by pressing from 
above with the pointed item, then remove the holder.

2

3

Return the battery holder to its original state.

4

Before Using the Projector

An insulation sheet has been inserted for protection during transportation prior 
to shipping. Please pull out and remove the sheet before use.

Insulation sheet

Handling of the Remote Control

•  Do not subject the remote control to a strong shock such as dropping it from a table. Doing so could 

damage it and render it inoperable.

•  Do not expose it to water or other liquid. If the remote control becomes wet, wipe it dry immediately.
•  Avoid exposure to heat and steam. Remove the coin-type lithium battery when the remote control will 

not be used for an extended period.

•  Do not disassemble or heat the coin-type lithium battery, nor throw it into a fire.
•  Please follow the disposal method of your region in disposing of the used coin-type lithium battery.
•  The remote control may fail to operate or performance may worsen when it is used near an inverter 

type fluorescent lamp.

•  Please store the coin-type lithium battery in a place that is out of the reach of children. If the battery is 

swallowed, promptly seek the care of a doctor.

•  Please handle the remote control with care, since there are some operations available only with it.

CAUTION

NOTE: 

When it is time to replace the battery, please purchase a CR2025 coin-type lithium battery. The use of batteries having a 

different shape such as the CR2032 may make removal difficult.

Summary of Contents for iP-40


























































Reviews: