manualshive.com logo in svg

Avigilon 12C-H4A-4MH-360, Installation Manual

Share
Download
Avigilon 12C-H4A-4MH-360 Installation Manual Download Page 24

6. Connect the network cable to the Ethernet port (a) and the external power/audio/digital I/O cable to its

connector (b). Secure the connections by turning them clockwise (c).

The Link LED will turn on once a network link has been established.

7. Check that the Connection Status LED indicator indicates the correct state. For more information, see

Connection Status LED Indicator

on page 62.

(Optional) Configuring microSD Card Storage

To use the camera's SD card storage feature, you must insert a microSD card into the card slot.

It is recommended that the microSD card have a write speed of class 10 or better. If the microSD card does not
meet the recommended write speed, the recording performance may suffer and result in the loss of frames or
footage.

1. Insert a microSD card into the camera.

CAUTION —

Do not force the microSD card into the camera or you may damage the card and the

camera.

2. Access the camera’s web interface to enable the onboard storage feature. For more information, see the

Avigilon High Definition H.264 Camera Web Interface User Guide

.

(Optional) Configuring microSD Card Storage

24

Summary of Contents for 12C-H4A-4MH-360



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands