Avidyne FlightMax EX5000 Pilot'S Manual Download Page 43 | Manualshive

Page: 43 / 50

background image

FlightMax EX5000

-40-

600-00105-000 Rev 01

Appendix - Lightning Messages

Lightning Messages

& Colors

Meaning

Recommended

Pilot Action

Lightning Sensor is
Operating Normally

Lightning source is operating in
a normal state from a
recoverable fault that was
previously acknowledged.

Acknowledge

Lightning Sensor is in
Noise- Monitor Mode

Lightning source is in
Noise- Monitor Mode.

Have maintenance check
configuration and
installation.

Lightning Sensor is in
Demo Mode

Lightning source is in Demo
Mode.

Have maintenance check
configuration and
installation.

Lightning Sensor is in
Test Mode

Lightning sensor in a self- test
mode.

Acknowledge

Lightning Sensor
ERROR

MFD receives a "recoverable
fault" notification.

Have maintenance check
configuration and
installation.

Lightning Sensor has
FAILED

MFD receives a "fatal fault"
notification.

Have maintenance check
configuration and
installation.

Lightning Sensor is Not
Communicating

MFD receiving no data from the
lightning sensor.

Have maintenance check
configuration and
installation.

Lightning Ahead

Stormscope is indicating
discharge activity horizontally
within ± 22 ° of the aircraft nose
and within 75nm.

Determine location of
lightning and avoid.

Lightning Heading
Source Failed

Stormscope is configured as a
heading source and a "fatal
heading fault" is received.

Have maintenance check
configuration and
installation.

Lightning Heading
Source OK

Stormscope is configured with
heading input.

Acknowledge

Lightning Antenna
Location Changed

Stormscope antenna location
disagrees with MFD setting.

Have maintenance check
configuration and
installation.

«
...
41
42
43
44
45
...
»

Summary of Contents for FlightMax EX5000



















































Reviews:

No comments

Related manuals for FlightMax EX5000

Brand: ISA Pages: 36

Brand: VALERA Pages: 2

Brand: Tecnodom Pages: 40

Jolly Gelato 1179

Brand: ifi Pages: 40

Brand: Garmin Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands