Avidyne FlightMax EX5000 Pilot'S Manual Download Page 20 | Manualshive

Page: 20 / 50

background image

600-00105-000 Rev 01

-17-

FlightMax EX5000

5) Engine Page - Cylinder Temperatures
Turbine Inlet Temperature -

Indicates the

Turbine Inlet Temperature in degrees

Fahrenheit for Saratoga II-TC and Piper 6XT

Aircraft. The numericTIT indication is above

the bar along with an up/down trend arrow.

Exhaust Gas Temperature (EGT) -

Indicates

the exhaust gas temperature of each cylinder

in degrees Fahrenheit as a bar graph. The

individual EGT of each

cylinder is also displayed as a numeric indi-

cation above each bar. An up or down trend

arrow will also appear below this numeric

indication to indicate whether a cylinder's

EGT is rising or falling.

Cylinder Head Temperature (CHT) -

Indicates the temperature in degrees

Fahrenheit of each engine cylinder head as reported by the DAU. The individual

temperature of each cylinder is also displayed as a numeric indication above each

bar. A white up or down trend arrow will also appear above or below this numeric

indication to indicate whether a cylinder is rising or falling in temperature.

Absolute -

Selects the “absolute” mode for EGT/TIT display. Absolute mode is the

default display mode, which indicates the current exhaust gas temperature for each

cylinder.

Normalize -

Selects the “normalize” mode for the EGT/TIT display. Upon activation,

the display will establish all of the current EGT’s or TIT at a zero point.

In Normalized mode, the bar graphs will indicate overall changes in temperature rather

than displaying the actual temperature values as in absolute mode.

Engine Instruments - Temperatures

«
...
18
19
20
21
22
...
»

Summary of Contents for FlightMax EX5000



















































Reviews:

No comments

Related manuals for FlightMax EX5000

Brand: Barco Pages: 2

Brand: AEA Technology, Inc. Pages: 126

Brand: Alto-Shaam Pages: 29

G1000 Diamond DA42NG

Brand: Garmin Pages: 644

Glo-Ray GRCD-2PDG

Brand: Hatco Pages: 2

UltraView iOP3200W

Brand: I-Tech Pages: 1

Brand: Igloo Pages: 36

Dreamoc Diamond

Brand: Realfiction Pages: 8

Brand: Oscartielle Pages: 52

Brand: Tecnodom Pages: 52

Brand: Vollrath Pages: 6

Brand: Ideal AKE Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands