AVer E5016 User Manual Download

Page: 120 / 191

111



Dropbox:

Upload the alarm video clip to the Dropbox space that user has

setup.

a. Get a Dropbox account. Go to Dropbox website and follow the instruction

to get a Dropbox user account.

b. Copy the below URL to your browser.

http://www.aver.com/Dropbox

c. Using your Dropbox account to login and click

“

Allow

” to enable Dropbox

WAN storage function.

d. Then, user will see the authorization code is displayed. Keep this web

page open and open a new web page.

e. Enter the below URL to enter authorization code. Please make sure your

PC can connect to NVR/DVR server through internet.

http://NVR/DVR IP/oauth2.html

ex: http:// 10.1.1.3/oauth2.html.

Next, NVR/DVR server will require login authentication. Enter the login

username and password of NVR/DVR server.

g. Then, authorization code input page is displayed. Copy the authorization

code into the

Authorization Code

column and click

Apply

h. Next, go to alarm action setting to setup FTP transmission via FTP (see

also

Chapter 2.12.2



Upload Video Clip



Select Camera:

Select the camera that the images will be captured and send

when the any alarm is triggered.



Before alarm (sec.)/After Alarm:

send the recorded image before and after

alarm occurs, enter the time that before alarm occurs in

Before alarm (sec.)

and

After alarm

Summary of Contents for E5016
































































































































































































Search results

Summary of Contents for E5016

Reviews:

Related manuals for E5016

Brands by name

Popular brands

AVer E5016, User Manual

Search results

Summary of Contents for E5016

Reviews:

Related manuals for E5016

Brands by name

Popular brands