Avenview HBT-C6POE-SET Instruction Manual Download Page 13 | Manualshive

Page: 13 / 20

Avenview HBT-C6POE-SET Instruction Manual Download Page 13

www.avenview.com

Page 10

6.

INSTAllATION (HBT-C6pOE-SET)

To setup Avenview HBT-C6pOE-SET please follow these steps for connecting to a device:

- Turn off all devices including monitors / TV
- .Connect to a HDMI source (such as a Blu-Ray Disc player) to the Transmitter HBT-C6pOE-S/Sp4/8 or Matrix 4x4/8x8
- Connect HBT-C6pOE-R 100m or HBT-C6pOE-Rl 60m with a CAT5/6/7 cable with shielded ends, then connect to

display with HDMI cable.

- plug in power for the Tx.
- plug in the IR BlASTER: into IR BlASTER in this case and the blinker on the IR eye (Source)
- plug in the IR Extender to IR EXTENDER in this case to receive IR Signals from Remote
- power on the HDMI display
- power on HDMI Sources.

NOTE:The QUALITY and TRANSMISSION of the video signals depends on the characteristics and quality of the

UTP cables. Higher resolutions and longer transmission distances require low skew cables (<25ns/100m) for

best performance.

Unshielded CAT6 with metal RJ-45 connectors is recommended.

«
...
11
12
13
14
15
...
»

Summary of Contents for HBT-C6POE-SET





















Reviews:

No comments