manualshive.com logo in svg

Avaya BSGX4e, Installation Manual

Share
Download
Avaya BSGX4e Installation Manual Download Page 32

BSGX4e Business Gateway Installation Guide

32

Release 01.01

NN47928-303

Upgrading software using the Web interface

This section describes how to upgrade the device software through the Web user 
interface (Web UI). This upgrade procedure assumes that the BSGX4e unit is 
installed into a working IP network as described in 

Installation (page 15)

. 

Requirements

To upgrade the BSGX4e software using the web UI, you must have the following:

„

A workstation on which you can run one of these Internet browsers: 

Microsoft 

Internet Explorer

 or 

Mozilla FireFox

.

„

The IP address of the BSGX4e. If you connect from the WAN, use the eth0 address. 
If you connect from the LAN, use the eth1 address. The procedure for showing the 
IP address is described under 

IP Address/Mask for eth0 (page 23)

.

„

The logon name and password for a user account that has administrator 
capabilities, such as the default account nnadmin.

„

The location of the file containing the upgrade software. The file must be on the 
workstation; its location is entered during the upgrade procedure. Select the file 
from the workstation directories with the Browse button.

Note: To acquire the upgrade software, contact 

"How to get help" on page 11

.

Logging on to the Web user interface

1. Start the Web browser on the workstation.

2. On the entry line of the Web browser, enter the IP address of the BSGX4e unit. 

If the workstation is connected through the LAN, enter the eth1 address; if the 
workstation is connected through the WAN, enter the eth0 address:

For example, assuming that the eth1 IP address has not be changed from its 
default, enter the following to log on from a workstation on the LAN:

n

HTTP:

http://192.168.1.1

n

HTTPS:

https://192.168.1.1

3. The logon window opens and requests a user name and password:

Summary of Contents for BSGX4e

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands