background image

QA47.03 installation manual sola-cure 2020 rev c. 

 

                         

Auxano Technologies Ltd, www.sola-cure.com 

 

OPERATION 

 

35.

 

Sola-Cure window blinds are available as a self locking (SL) or constant tension (CT) option. However 

this does not affect how the blind is operated. 

d.

 

Self-locking (SL).

 The blind can be stopped at various points of retraction and will maintain 

that position without using the pulley clamp. A short, firm pull down on the blind (using the 

cord or handle) will release the locking mechanism and the blind will fully retract. 

e.

 

Constant tension (CT)

. The blind can be stopped at any point of retraction and maintain that 

position. To do this, the operator must use the pulley clamp. If the clamp is not engaged on 

to the cord, the blind will retract fully. 

36.

 

To operate the blind, ensure the clamp is in the release position (depending on how the clamp is 

positioned, the release position can either be fully to the left or right). 

37.

 

Pull the cord through the clamp to draw down the blind. When the blind is in a suitable position, 

rotate the arm on the clamp fully to clamp the cord (for SL and CT type blinds) 

38.

 

To return the blind fully inside the cassette, release the clamp. CT blinds will immediately retract. For 

SL type blinds, a short, firm pull of the cord will retract the blind.  

CLEANING 

 

39.

 

For cleaning of the film, we recommend the use of a feather duster or dry dust cloth.  

40.

 

For stubborn stains on the film, methylated spirits on a cloth can be used. Caution: Do not press hard. 

41.

 

Pull down the blind fully and gently wipe/dust the film on both sides 

 

APPENDIX 

 

42.

 

Appendix A attached – Loose items. 

CONTACT 

 

Auxano Technologies Ltd, United Kingdom 

e-mail: 

[email protected]

 

Tel: +44 (0) 161 643 6060 

Web

www.sola-cure.com

 

 

 

 

Summary of Contents for SOLA-CURE










Reviews: