background image

B) Distance from human habitat.
     • Install your turbine with some distance from the human activity areas as 
     not to disturb your neighbors and animals around. The noise and 
      vibration element cannot be got rid of even if this wind turbine offers 
      the lowest noise than any others on the market. The better location of 
      your Turbine requires avoiding personnel or animal activities within a 
        33 ft (10 m) radius, and human habitation and wildlife within a 66 ft (20 m) 
        radius.
   •The rooftop may not be the best place for your Turbine. Here are three   
         reasons.
       a. The flow is more turbulent above the rooftop and leads to low wind 
             power availability.
         b. The stress the pole kit sustains varies in rooftop constructions. 
             Evaluation and stability cannot be guaranteed.
        c.  The slight noise and vibration still affect sleep for some sensitive 
             people and animals. 

C) Distance from MPPT controller and battery bank.
D) Any local zoning restrictions.
E) Clearance of power lines or any overhead connection.

3

Summary of Contents for 1500 Watts Wind Turbine

















































Reviews:

Related manuals for 1500 Watts Wind Turbine