background image

Page 5

IronHorse GSDA-DP-S User Manual –  1st Edition – 09/18/2019

w

arranty

AutomationDirect, Inc. (ADC) warrants its products to be free from defects in material and 

workmanship. The exclusive remedy for this warranty is ADC factory replacement of any part or parts 

of such product which shall within 12 months after delivery to the purchaser be returned to ADC 

factory with all transportation charges prepaid and which ADC determines to its satisfaction to be 

defective. This warranty shall not extend to defects in assembly by other than ADC or to any article 

which has been repaired or altered by other than ADC or to any article which ADC determines has been 

subjected to improper use. ADC assumes no responsibility for the design characteristics of any unit 

or its operation in any circuit or assembly. This warranty is in lieu of all other warranties, express or 

implied; all other liabilities or obligations on the part of ADC, including consequential damages, are 

hereby expressly excluded.

NOTE:  Carefully check the GSDA-DP-S for shipping damage. Report any damage to the carrier 

immediately. Do not attempt to install the device if visible damage is evident to either the circuit or 

to the electronic components..

s

PecificatiOns

GSDA-DP-S Specifications

Electrical

Line Input Voltage

85-265 VAC

Line Input Frequency

48-62 Hz

Voltage Signal Input

0-10 VDC

Voltage Signal Output

Min:

0�1-5 VDC

Max:

0�1-20 VDC, 10mA

mA Signal Input

4-20 mA

mA Signal Output

4-20 mA

Display Range

Default:

0-100�0%

Max:

-9999 – 9999

Units of Operation

Programmable

Onboard Power Supply (Externally Accessible)

5V @ 500mA

Voltage Regulated Supply Output Range

24VDC ± 5%, 200mA

Mechanical

Display Type

LED, red, 4 digit, 1/2” height

Housing Type (with supplied gasked in NEMA 

4X panel)

1/8” DIN NEMA 4X

Connector Style

3�5mm and 5mm European style

Terminus Block Torque Setting

4�4 in-lb [0�5 N

m] maximum

Faceplate Material

Polycarbonate with Lexan overlay

Housing Material

Aluminum

Length (Required Panel Depth)

4�625” [117�48 mm]

Faceplate Width

4�539” [115�29 mm]

Weight

14�4 oz [408�22g]

Environmental

Operating Temperature Range

-10

°

C to 45

°

C [14

°

F to 113

°

F]

Operating Humidity Range

95%, non-condensing

Summary of Contents for IronHorse GSDA-DP-S

















Reviews: