background image

WARRANTY AND EXCLUSION OF LIABILITY

Subject to all of the matter set out below, Automatic Technology Australia Pty Ltd (“ATA”) warrants for twenty four (24) months
from the date of purchase (specified in the receipt sales docket) that the Garage Door Opener System contained in the
accompanying  packaging (the “Product”) is free of any defects in material and workmanship rendering it unmerchantable.

This warranty referred to above applied only where:

a) the consumer seeking to rely on the said warranty;

1) returns the Product which it claims to be defective; and
2) presents the relevant sales docket and this warranty document, to the retailer from whom the Product was purchased 

to confirm that date of purchase; and 

b) the purchaser notified ATA or the retailer from whom the Product was purchased of the alleged defect in the Product
immediately upon experience or learning of the alleged defect.

Except for the warranty against defects in material and workmanship set out above, ATA gives no warranties of any kind
whatsoever, whether express or implied or whether statutory or at common law, in relation to the Product, and all warranties of
fitness for particular purpose and other warranties of whatsoever kind relating to the Product are hereby disclaimed. Without 
limiting the generality of the foregoing, ATA disclaims any liability of whatsoever nature in respect of any claim or demand loss
or damage which arise out of;

a) accidental damage to or normal wear and tear to the Product or to the Product’s components;
b) flood, rain, water, fire or lightning;
c) incorrect, improper or unreasonable maintenance and/or use;
d) installation, adjustment or use other than ATA which is not in accordance with the instructions set out in installation 

instructions incorporated in the document;

e) attempted or complete modification or repairs to the Product carried out by a person who is not authorised by ATA to carry out 

such modification or repairs;

f) faulty or unsuitable wiring of structure to which the Product is fixed or connected; and
g) radio (including citizen band transmission) or any electronic interference.
h) blown fuses or damage caused by electrical surges.
i) damage caused by insects.
j) lack of proper maintenance and care for the garage door and garage door opener. Failure to have the door serviced an

n

ually m

a

void this warranty.

k) installation of the opener on a commercial or industrial door or in a commercial or industrial situation.

ATA’s liability under the warranty set out above is limited, at ATA’s absolute option, to replacing or repairing the Product which
ATA, in its unfettered opinion, considers to the defective either in material and/or workmanship or to credit the consumer with the
price at which the Product was purchased by the consumer.

Where the Product is retailed by any person other than ATA, except for the warranty set out above, such person has no authority
from ATA to give any warranty or guarantee on ATA’s behalf in addition to the warranty set out above.

AUTOMATIC TECHNOLOGY AUSTRALIA PTY LTD

ABN 11 007 125 368

17-19 Advantage Rd, Highett, Victoria, Australia 3190

Tel: +61 3 9532 2788   Fax: +61 3 9532 2799

Web: www.ata-aust.com.au   Email: [email protected]

© January 2004 All Rights Reserved. SecuraCode

®

and SecuraLift

®

are registered trademarks of Automatic Technology Australia Pty Ltd. In an ongoing commitment

to product quality ATA reserve the right to change specifications without notice. E&OE.

Printed For Export.

Purc

h

ased From ___________________________________ Phone ______________________

Installed By _______________________________________ Date _______________________

Serial No. ________________________________________

Summary of Contents for GDO-2 SecuraLife





















Reviews: