Installation
937
Series
0208
1.02
Place level in position A, and adjust the
bottom leg levelers, and repeat in
positions B & C
DOOR
B
C
A
The 937 Line is assembled and packed so that a
minimum amount of time is necessary for
preparation to install it on location. The following
steps are recommended to insure correct
unpacking.
1.
Shipping Damage
: Thoroughly inspect the
exterior of the carton for damage which may
have occurred during shipment. Report any
damage to delivering carrier and follow their
instructions.
2. Remove the remainder of the packing
material. On machines shipped with the lock in
place, the keys are taped inside the delivery
bin.
NOTE: On the machine, the weight
concentration is toward the back of the
cabinet. Trucking and lifting should be
done from the back. CAUTION should be
taken when trucking from side.
3. On machines with lock in place, first unlock
and turn handle to open door. When no lock
is furnished, remove clip and turn handle.
Swing door to its full open position.
4. Remove all additional packing material from
the machine.
5.
Warranty:
The warranty card is attached to
the cover of this manual. It must be filled out
in full and mailed at once to insure coverage.
Leveling the Machine
on location is important for
the proper function of the machine. There are four
leveling screws in the legs of the machine to make
any necessary adjustments. After positioning the
machine, level it from front to rear and right to left
directions. After leveling, turn front right (lock side)
leveling screw in about one-half turn to drop this
corner slightly to make the door easier to close
and lock.
Locating the Machine
the 937 is designed to be
used with a Bev-Max 2. It should be placed 1 ½”
to the right of the Bev-Max (see figure A). A set
of spacers (part # 9371008) is included with the
Satellite and should be installed on the Satellite
cabinet. These spacers will give you the proper
clearance between the BevMax and Satellite.
IMPORTANT
: A set of anchoring brackets is
included with each machine. This kit is located
in the bottom of the machine with complete
instructions. It is recommended that this kit be
installed during set-up to prevent shifting of
the machine.
1 ½ Inches
Figure A: 1 ½ inches separation between
the 2 machines is required.
V2.3
Summary of Contents for PREMIER 937 SATELLITE
