background image

Trademarks

 

Autel

®

  and  MaxiCharger

®

  are  trademarks  of  Autel  Intelligent  Technology  Corp.,  Ltd., 

registered  in  China,  the  United  States  and  other  countries.  All  other  marks  are 
trademarks or registered trademarks of their respective holders. 

Copyright Information 

No part of this manual may be reproduced, stored in a retrieval system or transmitted, in 
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise 
without the prior written permission of Autel. 

Disclaimer of Warranties and Limitation of Liabilities 

All  information,  specifications  and  illustrations  in  this  manual  are  based  on  the  latest 
information available at the time of printing. 

Autel reserves the right to make changes at any time without notice. While information of 
this  manual  has  been  carefully  checked  for  accuracy,  no  guarantee  is  given  for  the 
completeness and correctness of the contents, including but not limited to the product 
specifications, functions, and illustrations. 

Autel  will  not  be  liable  for  any  direct,  special,  incidental,  indirect  damages  or  any 
economic consequential damages (including the loss of profits). 

IMPORTANT 

Before operating or maintaining this unit, please read this manual carefully, paying extra 
attention to the safety warnings and precautions. 

For Services and Support: 

Web: 

www.autelenergy.com

 

Tel: +49 (0) 89 540299608 (Europe) 

0086-755-2267-2493 (China) 

Email: 

[email protected]

 

For technical assistance in all other markets, please contact your local selling agent. 

 

 

 

Summary of Contents for MaxiCharger























































Reviews: