Autel Maxi US AC W12-H Installation Manual Download Page 3

• 

Install your charger on a flat and vertical surface capable of supporting its weight (e.g., a finished wall or pedestal). The 

maximum weight of a MaxiCharger AC Wallbox Home is approximately 6.7 kg (14.8 lbs.).

• 

Install the charger in a location that allows the charging cable to remain within its bending tolerance.

• 

Position the charger in a location where it is not vulnerable to being damaged

.

  1. Determine the desired charging amperage and if the desired circuit rating requires a hardwired circuit. Choose based on 

the electrical capacity in the panel, the desired speed of charging, and whether the user prefers a NEMA plug-in or hard-
wired installation. 

Getting Started

Preparing for Installation

Location

Positioning

LED Indicators

• Flashing Green: 

The charger is connected to a mobile device via Bluetooth.

• Flashing Blue: 

The charger is connected to the accessory VCI (Vehicle Communication

   Interface) via Bluetooth. (VCI sold separately.)

• Flashing Cyan: 

The charger is connected to a mobile device and a VCI device

   simultaneously via Bluetooth. (VCI sold separately.)

• Not Illuminated: 

The charger is not connected via Bluetooth.

• Illuminated: 

The RFID function is enabled. You can use the RFID card to start and stop

   charging.

• Not Illuminated: 

The RFID function is disabled.

LED

Power LED

Internet
Connection LED

Charging
LED

Bluetooth
Connection LED

RFID LED

Description

• Solid Green: 

The charger is on.

• Not Illuminated: 

The charger is off.

• Flashing Yellow: 

Data transmission has started and/or firmware is upgrading.

• Solid Yellow: 

Firmware upgrade has failed.

• Solid Blue: 

Data transmission has failed; will illuminate in five seconds.

• Solid Blue: 

An EV is connected.

• Flashing Blue: 

An EV is charging as scheduled.

• Flashing Cyan: 

The charger is reserved for charging.

• Flashing Green: 

An EV is charging.

• Solid Green: 

A charging session has ended.

• Not Illuminated: 

The charger is not connected.

• Solid Orange: 

A recoverable error has occurred.

• Solid Red: 

An irrecoverable error has occurred. (Please contact support.)

• Solid Green: 

The charger is connected to the backend of the charging management system.

• Not Illuminated: 

The charger is not connected to the backend of the charging management

   system.

Circuit Rating

50 A

40 A

40 A

32 A

Up to 38 miles/61 km

Up to 30 miles/48 km

yes

yes

yes

yes

Max Load

Estimated Range per Hour

NEMA Plug-in

Hardwire

3

Summary of Contents for Maxi US AC W12-H














Reviews: